series am2gw-nz 2 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r6.b 1 of 3 north america only features: models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) max capacitive load ( f) efficiency am2gw-2403s-nz 9-36 3.3 500 1500 1200 73 am2gw-2405s-nz 9-36 5 400 1500 820 75 am2gw-2409s-nz 9-36 9 222 1500 680 78 am2gw-2412s-nz 9-36 12 167 1500 470 82 am2gw-2415s-nz 9-36 15 133 1500 330 81 am2gw-4803s-nz 18-72 3.3 500 1500 1200 72 am2gw-4805s-nz 18-72 5 400 1500 820 76 am2gw-4809s-nz 18-72 9 222 1500 680 78 am2gw-4812s-nz 18-72 12 167 1500 470 81 am2gw-4815s-nz 18-72 15 133 1500 330 80 models dual output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) max capacitive load ( f) efficiency (%) am2gw-2405d-nz 9-36 5 200 1500 330 76 am2gw-2409d-nz 9-36 9 111 1500 270 78 am2gw-2412d-nz 9-36 12 83 1500 220 82 am2gw-2415d-nz 9-36 15 67 1500 180 81 am2gw-4805d-nz 18-72 5 200 1500 330 75 am2gw-4809d-nz 18-72 9 111 1500 270 77 AM2GW-4812D-NZ 18-72 12 83 1500 220 81 am2gw-4815d-nz 18-72 15 67 1500 180 80 input specifications parameters nominal typical maximum units voltage range 24 48 9-36 18-72 vdc filter capacitor maximum rating 24 vin 48 vin 40 80 vdc peak input voltage time 100 ms on/off control on ? low or open; off ? high on/off input current 5 10 ma * exceeding the maximum pe rmissible value of 20ma for the input on /off current will damage the converter. isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 1500 vdc resistance at 500vdc > 1000 mohm capacitance 80 pf ? rohs compliant ? operating temperature -40 o c to + 85 o c ? ultra wide 4:1 input range ? continuous short circuit protection ? remote on/off control ? high efficiency up to 82% ? 9 pin sip package ? low ripple and noise
series am2gw-nz 2 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r6.b 2 of 3 north america only output specifications parameters conditions typical maximum units voltage accuracy 3 % short circuit protection continuous short circuit restart auto recovery line voltage regulation ll~hl 0.75 % load voltage regulation load 10~100% 1.5 % temperature coefficient 0.03 %/ o c ripple & noise at 20mhz bandwidth 100 mv p-p general specifications parameters conditions typical maximum units switching frequency 100% load, vin nominal >100 550 khz operating temperature with derating above 71 o c -40 to +85 o c storage temperature -50 to +125 o c temperature rise full load 15 35 o c cooling free air convection humidity 95 % case material non-conductive black plastic (ul94v-0 rated) weight 7 g dimensions (l x h x w) 1.02 x 0.37 x 0.49 inch 26.00 x 9.60 x 12.00 mm mtbf >1 000 000 hrs (mil-hdbk -217f, ground benign, t=+25 o c) note: all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated outpu t load unless otherwise specified pin out specifications dimensions derating -40 -20 0 2040 6080 100 ambient temperature o c 100 80 60 40 20 0 free air convection 71 o c safe operating area output power (%) 85 pin single dual 1 - v input - v input 2 + v input + v input 3 on/off control on/off control 6 + v output + v output 7 n.c. common 8 n.c. n.c. 9 - v output - v output 2.90 (0.11) 26.00 (1.02) 0.50 (0.02) 0.50 (0.02) 4.00 (0.16) 2.54 (0.10) 2.000 (0.079) 123 67 8 9.60 (0.37) 0.300 (0.012) 0.50 (0.02) 9.60 (0.37) printed face 12.50 (0.49) 9
series am2gw-nz 2 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r6.b 3 of 3 north america only control on/off pin connection example: the voltage could be applied through a limiting resistor and a sw itching diode. the converter is in a low power mode during high level phase. note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com.
|
